Page 691

2017roadiron-cruiser_en

691 PERFORMANCE CAMS ALL 2007-UP TWIN CAMS AND 2006 DYNAGLIDE PERFORMANCE CAMS ALL 2007-UP TWIN CAMS AND '06 DYNAGLIDE Grind Timing CL Duration .053 Duration .020 Valve Lift Lift @ TDC Application Stock ‘06-Dyna Intake Exhaust 02/34* 42/-03* 106 112.5 216 219 256 259 .473 .474 .087 .110 Stock ‘06 Dynaglide cam data listed for reference: All 2006 Dynaglides are fuel injection only; no carburetors. Stock Intake Intake Exhaust 09/25* 42/-03* 107 112.5 196 219 234 259 .473 .474 .087 .110 Stock 07-Up specs listed for reference. Very short Intake duration is stock on most 07-12 engines. 349-4762 26H 11/35* 41/09* 102 106 226 230 262 266 .490 .490 .138 .120 Bolt-in cam: 96 - 103 inches and stock compression ratio. Great for two up touring, this cam will add torque and HP at lower and middle RPM ranges. (1800-5200 RPM). 349-4763 31H 10/46* 52/08* 108 112 236 240 272 276 .510 .510 .131 .120 Great cam for motors with 96 inches and 9.8 to 10.2 C.R. Lower TDC lift for easy installation. Similar to TW37 with timing setup for higher compression. (2400-5600 RPM). 349-4766 50H 20/48* 54/18* 104 108 248 252 283 287 .510 .510 .184 .168 Designed for easy installation in 96-103 inch motors with stock heads and 9.5 to 9.8 CR. (2400 to 6000 RPM). (*) Timing and duration for .053 cam lift (**) Lobe Centerline angle TWIN CAM CHAIN DRIVE CAMSHAFT 99-06 "EXCEPT 06-DYNA" TWIN CAM CHAIN DRIVE CAMSHAFT 99-06 "EXCEPT 06-DYNA" • Splined chain drive camshafts • Kits include: 1 roller bearing and 1 ball bearing • Designed for use with stock Harley-Davidson® hydraulic lifters • Can be installed on both carbureted and fuel injected models • Will not fit 06 DYNA Grind Timing Duration .053 Duration .020 Valve Lift Lift @ TDC Application Stock 88 Carburetors (A) -02/38* 42/-03* TWIN CAM 88™ GEAR DRIVE CAMSHAFT 99-06 "EXCEPT 06-DYNA" Twin Cam 88™ Gear Drive Camshaft 99-06 "except 06-Dyna" • Gear drive uses less engine power to operate and improves valve timing accuracy over stock chain drive camshafts • Dynamometer comparisons show gains of 4 horsepower over chain drive camshafts • Can be installed on both carbureted and fuel injected models • Sold as cams only, inner and outer gear kit 349-4730 and installation kit 349-4450 must be purchased separately. Note: 55 and larger require spring spacing. Grind Timing Duration .053 Duration .020 Valve Lift Lift @ TDC Application 216 219 255 259 .473 .474 .072 .110 GEAR DRIVE CAMS 2007-UP & '06 DYNA Touring and performance cams Stock 88 Carburetors (A) -02/38* 42/-03* Grind Timing Duration .053 Duration .020 Valve Lift Lift @ TDC Application 349-4772 31HG 10/46* 52/08* 236 240 272 276 .510 .510 .131 .120 Great cam for motors with 88+ inches and 10:1 CR. TDC lift means easy installation. Similar to 37HG but different timing. 2400-5800 RPM power range. Gear Drive Installation Kit (as shown) Replacement bearings are included in above kit: Inner Case Needle Bearings (two bearings required) 349-5204 ea Carbureted engine: stock cam data listed for reference. (Stock engine output is approximately 62 HP). Stock 88 Injectors (B) 02/34* 42/-03* 216 219 255 259 .473 .474 .087 .110 Fuel injected engine: stock cam data listed for reference. (Stock engine output is approximately 62 HP). 349-4726 37G 18/38* 46/14* 236 240 272 276 .510 .510 .174 .148 Hot street cams for 88 or 95 inches. 80+ rear wheel HP possible with well tuned 88 motor; more with 95. Smooth idle, broad torque (2200- 5600 RPM) Stock to 9.5 CR. 349-4734 55G 22/46* 52/20* 248 252 283 292 .550 .550 .197 .181 Great cam for 95 inch engines with 9.8 to 10.2 C.R. Max HP - torque at mid and upper RPMs (2600-6200). 349-4735 60G 24/56* 58/22* 260 260 296 296 .560 .560 .205 .192 For well prepped 95-103 inchers with 10.0 to 10.5 CR, 100+ HP is within reach. (2700-6500+ RPM). (*) Timing and duration listed for .053 cam lift. 216 219 255 259 .473 .474 .072 .110 Carbureted engine: stock cam data listed for reference. (Stock engine output is approximately 62 HP). Stock 88 Injectors (B) 02/34* 42/-03* 216 219 255 259 .473 .474 .087 .110 Fuel injected engine: stock cam data listed for reference. (Stock engine output is approximately 62 HP). 349-4722 TW55 22/46* 52/20* 248 252 283 292 .550 .550 .197 .181 Great cams for 95 inch engines with 9.8 to 10.2 CR. Max HP and torque at mid & upper RPMs (2600-6200) Touring and performance cams (*) Timing and duration listed for .053 cam lift. (*) Timing and duration listed for .053 cam lift


2017roadiron-cruiser_en
To see the actual publication please follow the link above