Page 617

2017moto_en

589 NOTES (CONT.) 090 We recommend using 14-0112 lever with this kit (not included in kit) 091 “For use with stock throttle bodies. Stock reel is _33.4 mm. IMPORTANT - The stocktwist throttle assembly on this model incorporates an on/off switch, mode switch, andstarter button. The Motion Pro 11-0057 accessory switch only has an on/off switchand starter button, and cannot be used to replace the original switching functions onthe stock throttle assembly. In order to install the Revolver VR kit and retain all thenecessary switching functions, owners of this model will need to install longer after market handlebars (at least 50 mm longer than stock on the right side) and use thestock throttle assembly mounted behind the Revolver VR throttle housing. The stocktwist throttle assembly can be modified to remove the throttle reel holder portion andleave just the necessary switches. This modification makes it narrower and uses lessspace on the handlebar.“ 092 Fits both California and Non-California models (49 state) 093 “Some models may require use of a slip barrel at the carburetor and/or thumbthrottle. (not included with cable). You can reuse the slip barrel that is on your vehicleor purchase this item separately from your local Suzuki dealer.“ 094 Fits front wheel. Drilling of rim may be required for installation on front rim. Orremove plug from rim where applicable 095 Revolver throttle kit featuring Chrome Revolver throttle housing. 096 Off road revolver throttle kits require a minimum of 200 mm of handlebar length inorder to provide sufficient clearance between Revolver throttle housing and hydraulicbrake lever 097 Throttle kit includes 11-0056 4x4 switch relocation plate 098 Polished aluminum. 2011 Stryker models which use polished levers areXVS13CACL,CAL, CAC0, and CA0. 2011 Stryker models which use black control leversare XVS13CAB and CACB (Black levers are not available for this model) 099 Will work with the stock Carb, S&S Super E & G with CV Bracket & late model MikuniHSR carbs for use with CV cables 100 Built 2/16/10 and After 101 Lower front brake cable only 102 Replacement clutch cable only. Does not include engine side mounting bracket. Forcomplete cable with bracket use part number 02-3007 (CRF250R) or 02-3008(CRF450R). Requires use of Motion Pro mounting bracket and will not work with stockHonda bracket. 103 Includes engine side billet aluminum mounting bracket. For replacement cable onlywithout bracket, use part number 02-3006. 104 3 inches longer than standard length Revolver throttle cable # 01-1106. Revolvercables can only be used with stock throttle body (or carburetor where applicable) andRevolver throttle 106 For use with stock throttle bodies. Revolver throttle kit for BMW S1000RR with vehicleproduction date range 09/08 - 03/12. Revolver Kits have cables specifically designedfor fitment on specific models, but the Revolver throttle itself is not model specific.Therefore, in some situations, the Revolver kit may not be a direct bolt on installationdue to space limitations on the stock handlebar. In some installations, it may benecessary to move other control components on the stock handlebar, shorten theRevolver throttle tube and grip, install longer aftermarket handlebars, or possibly allof the above. It is up to the end user to determine the best method for fitment on theirmotorcycle, and ensure that the Revolver kit is installed properly and with the correctclearances for safe operation. Installation should be done by a qualified mechanic andcarefully checked for proper function. Warning: Improper installation could result ingreat bodily injury or death. 108 Revolver Kits have cables specifically designed for fitment on specific models, butthe Revolver throttle itself is not model specific. Therefore, in some situations, theRevolver kit may not be a direct bolt on installation due to space limitations on thestock handlebar. In some installations, it may be necessary to move other controlcomponents on the stock handlebar, shorten the Revolver throttle tube and grip,install longer after market handlebars, or possibly all of the above. It is up to the enduser to determine the best method for fitment on their motorcycle, and ensure thatthe Revolver kit is installed properly and with the correct clearances for safe operation.Installation should be done by a qualified mechanic and carefully checked for properfunction. Warning: Improper installation could result in great bodily injury or death. 109 This control cable is supplied with a clutch perch adjuster (01- 0024) which must beinstalled with cable. 110 Note on installation: Route cable through side of steering head opposite side of CDIbox. If CDI box is mounted on the left side of steering head, route cable on the rightside of steering head and vice versa. If CDI box is not mounted on the steering head,route cable on the left of steering head. 112 Fits stock throttle housing. Use with accessory bar-end mounted hand-guards requiresdrilling out end cap, which will void warranty. Can be used with open end MX handguards without any modification. 117 01-0094 and 01-1170 reel diameter is 37mm. The OEM reel size for 07-12 RMZ 250and 2007 RMZ450 is 40mm, which will make the throttle a little slower and mayrequire free length adjustment on the throttle cable to make sure the throttle can befully opened. 120 When 06-103000 is used on Gas Gas models, 06-103000 is 50 mm (2”) longer thanOEM housing length. Fits stock throttle and stock carburetor. Remove OEM slottedcable adjuster from throttle and thread T3 cable directly into throttle housing.Disregard KTM installation instructions and use OEM cable routing. 123 Australian Model 127 Does not include hot start lever mount bracket where applicable. We recommend careful inspection of the pivot bolt when replacing a lever and that you replace the pivot bolt and lock nut if there are any signs of wear or if the prior lever suffered any impact damage.We also recommend that you replace the lock nut, if applicable, anytime the lever is removed.Pivot bolt and lock nut must be installed and tightened properly as recommended by the manufacturer of your motorcycle.Please remember to lubricate the pivot bolt per the factory service manual recommendations. 130 Requires 01-0013S adapter for 2013 KTM. Sold separately. 133 3 inches longer than standard length Revolver throttle cable # 01-1205. Revolver cables can only be used with stock throttle body (or carburetor where applicable) and Revolver throttle 138 We recommend careful inspection of the pivot bolt when replacing a lever and that you replace the pivot bolt and lock nut if there are any signs of wear or if the prior lever suffered any impact damage. We also recommend that you replace the lock nut, if applicable, anytime the lever is removed. Pivot bolt and lock nut must be installed and tightened properly as recommended by the manufacturer of your motorcycle. Please remember to lubricate the pivot bolt per the factory service manual recommendations. 139 01-0094 does not have anti grip rub flange. We recommend installing anti friction washer between grip and throttle housing. Washer readily available through your favorite local motorcycle store or Yamaha dealers. Yamaha OEM: 3Y1-26249-00-00. The lenght of 01-0094 is 4mm less than OEM throttle tube. 140 For use with stock throttle bodies/carburetors and Rev2 throttle assembly only. IMPORTANT: The Rev2 throttle does not have the starter and kill switch wiring or switches that are built into your stock throttle assembly. Use of the Rev2 Throttle requires an after market kill switch and starter button assembly (# 11-0098) not included in kit. Rev2 Kits have cables specifically designed for fitment on specific models, but the Rev2 throttle itself is not model specific. Therefore, in some situations, the Rev2 kit may not be a direct bolt on installation due to space limitations on the stock handlebar. In some installations, it may be necessary to move other control components on the stock handlebar, shorten the Rev2 throttle tube and grip, install longer after market handlebars, or possibly all of the above. It is up to the end user to determine the best method for fitment on their motorcycle, and ensure that the Rev2 kit is installed properly and with the correct clearances for safe operation. Installation should be done by a qualified mechanic and carefully checked for proper function. Warning: Improper installation could result in great bodily injury or death. 141 For use with stock throttle bodies. Stock reel is 33.4mm. IMPORTANT: The stock twist throttle assembly on this model incorporates an on/off switch, mode switch, and starter button. The Motion Pro 11-0098 accessory switch only has an on/off switch and starter button, and cannot be used to replace the original switching functions on the stock throttle assembly. In order to install the Rev2 kit and retain all the necessary switching functions, owners of this model will need to install longer aftermarket handlebars (at least 50mm longer than stock on the right side) and use the stock throttle assembly mounted behind the Rev2 throttle housing. The stock twist throttle assembly can be modified to remove the throttle reel holder portion and leave just the necessary switches. This modification makes it narrower and uses less space on the handlebar. Rev2 Kits have cables specifically designed for fitment on specific models, but the Rev2 throttle itself is not model specific. Therefore, in some situations, the Rev2 kit may not be a direct bolt on installation due to space limitations on the stock handlebar. In some installations, it may be necessary to move other control components on the stock handlebar, shorten the Rev2 throttle tube and grip, install longer aftermarket handlebars, or possibly all of the above. It is up to the end user to determine the best method for fitment on their motorcycle, and ensure that the Rev2 kit is installed properly and with the correct clearances for safe operation. Installation should be done by a qualified mechanic and carefully checked for proper function. Warning: Improper installation could result in great bodily injury or death. 142 Off road Rev2 throttle kits require a minimum of 200mm of handlebar length in order to provide sufficient clearance between Rev2 throttle housing and hydraulic brake lever. 143 For use with stock throttle bodies. Rev2 throttle kit for BMW S1000RR with vehicle production date range 09/08 - 03/12. Rev2 Kits have cables specifically designed for fitment on specific models, but the Rev2 throttle itself is not model specific. Therefore, in some situations, the Rev2 kit may not be a direct bolt on installation due to space limitations on the stock handlebar. In some installations, it may be necessary to move other control components on the stock handlebar, shorten the Rev2 throttle tube and grip, install longer aftermarket handlebars, or possibly all of the above. It is up to the end user to determine the best method for fitment on their motorcycle, and ensure that the Rev2 kit is installed properly and with the correct clearances for safe operation. Installation should be done by a qualified mechanic and carefully checked for proper function. Warning: Improper installation could result in great bodily injury or death. 144 Rev2 Kits have cables specifically designed for fitment on specific models, but the Rev2 throttle itself is not model specific. Therefore, in some situations, the Rev2 kit may not be a direct bolt on installation due to space limitations on the stock handlebar. In some installations, it may be necessary to move other control components on the stock handlebar, shorten the Rev2 throttle tube and grip, install longer after market handlebars, or possibly all of the above. It is up to the end user to determine the best method for fitment on their motorcycle, and ensure that the Rev2 kit is installed properly and with the correct clearances for safe operation. Installation should be done by a qualified mechanic and carefully checked for proper function. Warning: Improper installation could result in great bodily injury or death. 145 01-2765 Rev2 throttle kit features throttle cable set 01-1270 that is 3 inches longer than throttle cable 01-1269 included in Rev2 throttle kit 01-2764. 150 Replacement clutch cable only. Does not include engine side mounting bracket. 153 Routing is on left side for Beta models. 5 inches longer than oem cable. 154 Housing length on this control cable is one inch longer than OEM cable. 160 01-2784 Rev2 throttle kit features throttle cable set 01-1292 that is 3 inches longer than throttle cable 01-1289 included in Rev2 throttle kit 01-2783


2017moto_en
To see the actual publication please follow the link above