Page 515

2016snowmobile

WooDY’S CARBiDeRunneRS Flat-top® runner design Flattop® trail runners To provide steering traction on hard-packed or icy surfaces, carbide runners are an essential part of traction and control products. Woody’s carbide runners are designed to provide you with the added grip and turning ability you need for a variety of challenging conditions. Woody’s manufactures their runners with the finest carbide and steel. Extra long mounting bolts and flanged lock nuts allow for fast and easy installation. Our exclusive Flat-Top® surface provides maximum Flat-Top® runner has more support surface support. Our rear angle cut prevents catching when reversing or unloading. Balancing the length of carbide in your runner in ratio to the number of studs is a must. The number of studs you put in your track will determine the length of carbide you will need on your skis. Woody’s.the name you rely on for safety, performance and control. Now has a 60° Carbide For Better Traction 1-1/2” carbide wear pad 4” of 60° turning carbide Full-length carbide wear pads 10” of 60° turning carbide 4”extendertrailiii™ Flat-top® 10”ultra series This is a popular runner for trail riding. It has 4” of 60° turning carbide, with This premium performance carbide runner is designed for very energetic trail domed 1 1/2” carbide wear pads at each end of the full length hardweld. riders and cross-country racers who demand superb cornering control. The extra Woody’s offers the Extender Series to replace the manufacturer’s stock runners long 10” of turning carbide with a sharp 60° cutting edge provide that control. for added cornering control, especially when the trail begins to get icy. Our A high profile runner bar and full-length carbide wear pads protect the runner guideline for consideration of the Extender Series would be up to 72 studs from premature wear. This runner will handle heavily studded sleds - 192 or more installed in the track. studs for proper balance between the studs and this Ultra Series Bar. 1-1/2” carbide wear pad 6” of 60° turning carbide 6”trail Blazeriv™ Flat-top® This runner is for the trail rider looking for more performance in cornering power and control. The turning carbide is 6” long with a 60° edge. Hardweld covers the full length of the area between the turning carbide and the carbide wear top-Stock™ Series pads. It has a large 1/2” diameter bar for strength and 3/8” ski mounting bolts. Top-Stock™ is an economical hardweld runner designed for extreme service or This runner is designed to use with 72 to 144 studs installed in the track. It is utility applications. The 1/2” host bar with hardweld increases the depth of the essential that the track be studded when using this runner. runner for added controllability. Recommended for deep snow or snowmobiles with 48 or fewer studs installed. 1-1/2” carbide wear pad 8” of 60° turning carbide 8”executive™ Series Flat-top® The Executive Series runner is designed for performance trail riders and cross- country racers. The 8 inches of 60° carbide provides turning power for the experienced rider. The carbide of this runner must be balanced with a studded Woody’s® ACe™ RunneR track. A guideline to follow would be to have 144 to 192 studs installed in your Woody’s ACE™ single runner line utilizes a 3/8” x 1/2” preformed steel square track before considering this performance bar on the trail or cross-country course. bar. The ACE has a taller profile and is more aggressive, providing excellent control on rider forward sleds. Available in 8” carbide for trail users in our most popular number series. WARninG! Proper track studding is mandatory with the use of this runner. Dangerous loss of snowmobile control may occur without the proper studding amount installed in the track to balance with the 10” of carbide in the runner. 515


2016snowmobile
To see the actual publication please follow the link above