Page 803

2013 RI Cruiser

For pricing, visit www.motovan.com in the dealer section. 803 53-2333 53-2334 Big Twin Engine Rotator, from the Flywheel Sprocket Shaft Tool This tool is used to rotate the flywheel assembly when doing pushrod adjustments, when building big inch engines, or when checking operating clearances sush as piston to piston, or valve to valve. Also can be ised to hold the flywheel assembly from rotating when torquing the cam drive sprockets retention bolts on Twin Cams or pinion shaft nut on single cam models.This tool has been designed with a long socket design making it easier to use without the use of a 1/2” drive extension, on your 1/2” driver. For engine bench work we recommend the engine be bolted in a JIMS® engine stand. Use No. 1006T for Panhead, Shovelhead and Evo’s. Use JIMS® No.53-0568 for all ”A” engines, early and late 1999 to 2007 Twin Cams FL’s and FXD’s. Use JIMS® No. 53-1668 for 2000 to 2006 FXST’s. Caution: Not for use with pneumatic or electric impact. This tool is only guaranteed for use with hand drivers, “not impacts”. Use on Big Twins 1955 to 2006 except 2006 FXD’s. Use on 1999 to 2005 FXD. 53-2333 Use on 2006 and UP FXD + 2007 and UP Big Twin 53-2334 2006 Dyna 2007 Big Twin inner cam bearing installer tool Use this tool to press in the two inner cam bearings. JIMS® No. 53-0078 came bearings. This tool has been designed to press from letter side of the inner cam bearings, by putting all the pushing pressure to the very outer wall of bearing shell. Eliminating any damage to the bearings, cam and cases. This tool will stop at the case and set the bearing depth to .023” to .028” below the case surface. A must use for the longest bearing and cam life. Use with JIMS® Tool No. 53-0993 53-0993 Hose Repair Kit 1/4” – 5/16” Hose bared end is .3125 (5/16”), threaded end is 12mm. It can be used with either a .250” or .3125” hose. May also work to make up your own air tester kit, or for filling tires on the road, by threading into spark plug hole and at the other end of the hose is an air chuck fitting. Works well to repair JIMS® tool No.53-0095 leakdown tester, for the 12mm spark plug threads found on all Twin Cams, XL 1986 & later and Screamin Eagle EVO BT heads. 53-2329 Hose repair 2006 Dyna 2007 Big Twin case splitter tool Use this tool to “Break” the case sealant by pushing apart both case halves. Bolt (with supplied hardware) this tool to the primary mounting holes, hand thread-in pushing screw (do not used impact tools). Flywheels will be pushed from the left case. 53-0995 2006 Dyna 2007 Big Twin main bearing installer tool Use this tool to safely install a new main trans case bearing by using hand tools. Tool will hold bearing square to its bore, eliminating any marring of the bearing bore. This tool is used in the same manner as JIMS® Tool No. 53-0412 that you’ve been using for years. 53-0987 Balancer shaft removal tool This tool was designed to align and safely install a new balancer bearing, and counter-balancer shaft into the new Twin Cam 96” or 110” “B” Softail engine case. For removal of the balancer shaft from the engine case use JIMS® tool No.53-2317. Use on 2007 to present FXST. 53-2328 Installer 53-2317 Removal tool Oxygen Sensor Socket Tool This tool is used to remove or install the oxygen sensor on all closed loop fuel injected H.D. models. Socket has a 3/8” drive receiver or can be used with a 7/8” wrench. Socket will withstand up to 125 ft/lbs of torque. Use on all EFI models 2006 to present. 53-2330 Dyna main drive gear, bearing & seal installer tool Use this tool to safety install new main drive gear bearings and seal, with use of a small 1-ton press. This tool will hold bearings and seal square to it’s bore, eliminating any marring of the bearings and seals and installing both to the right depth. This tool is used in the same manner as JIMS® Tool No. 53- 0430 that you’ve used for years. 53-0986


2013 RI Cruiser
To see the actual publication please follow the link above