JIMS® Mega Nut for Cruise Drive™ Years ago JIMS was proud to design the original “meganut” for the precision minded bike builder. The meganut incorporates a machined clamping face tolerance, along with additional locking holes for a more precise and secure way to secure the pulley nut. By installing this mega nut correctly you can feel confident that your rear pulley will never come loose from your main drive gear. New for 2011, this nut is now available for late model Cruise Drive Transmissions. Use the JIMS pulley locknut socket tool and sprocket or pulley locker tool to make the complete installation accurate and easy! Use on all H-D 6-speed Cruise Drive Transmissions 2006 to present FXD’s and 2007 to present FLH’s and FXST’s. 53-2383 NTN™ Clutch hub bearing for Big Twins® Replacement bearing for clutch sprocket for Big Twins®. 50-070018 Fits Big Twins® late 84-90. Repl. Oem #37906-84 or #9025A 50-070019 Fits Big Twins® 1991-up. Repl. Oem #37906-90 Mega nut A cure for the loose pulley nut. The JIMS® Mega Nut has a lock plate built in. The Mega Nut can also be secured in several additional places by an easy drilling and tapping operation. Another JIMS® exclusive. Tighten nut with JIMS® tooI No. 53-0532 53-0062 Use on all 91-present XL’s. Use on 1985-2006, FL FXST, and FXR. Use on 1985-2005, FXD, and JIMS® 6-speed Note: JIMS® Mega nut will work with all belt drive pulleys, H.D.® or aftermarket, some aftermarket may need a hole drilled and tapped. Clutch release bearing kit Replaces H.D. OEM 37312-75, 37313-80 & 11096. 53-0133 Use on Big Twin® 1975-present 4 & 5-Speed transmissions Clutch disassembly washer • Easy to use tool works as follows: remove clutch pushrod adjusting screw lock nut, place compressor over screw, replace nut and tighten. • Tightening relieves tension on the clutch springs, easing removal and installation of stud nuts. 304-1430 41-E84 Big Twin Models 5 Stud clutch hub Fits Big Twin® models 1936-early 1984. Replacement parts 50-070067 5 Stud Pressure Plates 50-070018 Bearings 28-626N Fits XL® models 71-early 84. Replaces Oem# 37722-71 Road Iron™ High performance pressure plate Machined aluminum pressure plate eliminates even spring pressure. Works with 3, 5 or 10 finger clutch hubs. Fits Big twin® models 1941-early 1984. Repl. OEM 38018-41. 50-070054 Pressure plate Replacement studs for 3 Stud clutch hub 349-2707 Short stud. Repl. OEM37585-41. Sold each Road Iron Clutch hub nut lock tab for 41-E84 Big Twin® This clutch nut lock tab is for 41-early 84 Big Twin® models and replaces OEM #37503-41. Sold in pack of 10. 50-100154 Clutch Hub Nut Lock Tab Road Iron™ Cluch hub stud nuts for 41-E84 Big Twin® These stud nuts replace OEM #37581-47 on 41- E84 Big Twin® models. Sold in pack of three. 51-194994 Clutch hub stud nut Transmission sprocket nut Use on Big Twin® models. 1-1/2” - 24 Thread. Use with 53-0532 socket. 53-0411 Use on Big Twin® 1936-present Check for clearances on 4-Speeds Note: Includes Twin Cam 88TM and Baker by JIMS® 6-speed 400 For pricing, visit www.motovan.com in the dealer section.
2013 RI Cruiser
To see the actual publication please follow the link above