Page 428

2013 Moto En

428 Stret and double usage bikes cables (cont.) 001 Requires 4WD switch relocation kit part# 11-0024 (not included). 002 Requires 4WD switch kit 11-0033 (not included). 003 Requires 11-0032 4wd switch relocation kit (not included) 004 Top cable only 005 Also fits stock throttle 006 Built before 2/10/99 007 Built after 2/10/99 008 Requires 01-0033 carb cap 009 Use with stock carb(s) requires carb cap(s) (01-0023) & adjuster(s) (01-0013). Eliminates TORS system & stock carb cap(s). Requires idle kit (08-0045) when used with stock carb(s) (sold separately). Warning - Disables the T.O.R.S. system and will not shut down engine in case throttle sticks open. A stuck throttle could result in uncontrolled acceleration and great bodily injury or death. This product is intended for closed course racing by expert riders only. Improper installation could result in great bodily injury or death. User assumes all responsibility for proper installation and use of this product. 010 Fits stock carb with stock carb caps only 011 For use with stock throttle 012 Also fits stock throttle 013 Fits FCR 41 014 For use with FCR carbs 015 Fits Domino throttle to Keihin FCR 016 Fits stock thumb throttle 017 Fits handlebar mounted hot start lever 018 Warning - This kit disables the T.O.R.S. system and will not shut down engine in case throttle sticks open. A stuck throttle could result in uncontrolled acceleration and great bodily injury or death. This product is intended for closed course racing by expert riders only. Improper installation could result in great bodily injury or death. User assumes all responsibility for proper installation and use of this product. 019 Includes 4x4 Switch Relocation Kit. 020 Includes carb cap p/n 01-0020, cap is attached to cable. 021 Kit includes carb cap p/n 01-0022, remove 0020 & replace 022 Includes carb cap p/n 01-0021, cap is attached to cable. 023 Non CA models only (For 49 state) 024 CA models only 025 Requires 11-0026 4x4 Switch Relocation Kit for 4WD models (11-0026 sold separately) 026 Top cable only 027 T2 Gray cable 028 Rear hand brake 029 Rear foot brake 030 Works with stock throttle cable 031 WARNING. This throttle is extremely fast and is recommended for closed course off road racing by expert riders only. 032 Grips included 033 This cable will replace either push or pull throttle cables (both cables are the same) 034 Early 1984 only 035 Early 1976 only 036 Early 1980 only 037 Late 1984 only 038 Late 1976 only 039 Late 1989 only 040 Late 1988 only 041 Late 1978 only 042 Late 1985 only 043 Can only be used without cruise control 044 Early 1985 only 045 W/S&S Super E or G carbs. This cable replaces Idle or Throttle side cables. 046 01-0233 Fits pull and push side with stock throttle. Or use 01-0234 with Mikuni smooth bore kit and 01-0058 throttle assy. 01-0234 Fits push side of 01-0058 throttle. 01-0233 fits pull side of 01-0058 throttle. 047 Warning - Disables the T.O.R.S. system and will not shut down engine in case throttle sticks open. A stuck throttle could result in uncontrolled acceleration and great bodily injury or death. This product is intended for closed course racing by expert riders only. Improper installation could result in great bodily injury or death. User assumes all responsibility for proper installation and use of this product. 048 Warning - Agricultural throttle is for low speed farm use only. Not for sport or recreational use. 049 For adding optional Sigma electronic odometer sensor pick-up on SX models for 98-02 models use 10-0104 050 For adding optional Sigma electronic odometer sensor pick-up for 2003 and later models use 10-0103 051 Requires use of 01-0465 to stock front brake. 052 requires use of 14-0105 to stock front brake 053 For 2006 Polaris Sportsman 500 EFI built before 01/16/06 054 For 2006 Polaris Sportsman 500 EFI built after 01/16/06 055 With CDI only 056 With breaker points 057 01-1019 Cable for use with 01-0053 CR Pro throttle only. Not for 01-0056 CR Comp. Carb cap included. 058 For use with stock thumb throttle. Warning - Disables the T.O.R.S. system and will not shut down engine in case throttle sticks open. A stuck throttle could result in uncontrolled acceleration and great bodily injury or death. This product is intended for closed course racing by expert riders only. Improper installation could result in great bodily injury or death. User assumes all responsibility for proper installation and use of this product. 059 Does not fit SV650S 2003-2007; SV650SA 2007 060 Same as 08-0425 except 08-0372 has a 14 mm crankshaft thread protector 061 1.5 inches longer than stock 062 Sensor pin assembly not included with Motion Pro lever. Remove Sensor pin assembly from lever being replaced and install on new Motion Pro lever. 063 “Same puller body as 08-0372 (C08-0372A), but with thread protector C08-0257B.“ 064 Uses snap-in fitting at thumb throttle. OEM cable uses bayonet fitting at thumb throttle 065 4WD switch relocation kit 11-0033 included with kit 066 Specially designed for SV650S with clip-on bars. Routes through cylinder V. 067 Please check size needed, OEM changed rotors through production run.Puller size on some models may require 18mm flywheel puller 08-0116 068 Please check size needed, OEM changed rotors through production run.Puller size on some models may require 16mm flywheel puller 08-0027 069 Warning: This kit disables the stock throttle override system. This kit will not shut off the engine if your throttle or carb sticks in the open position. A stuck throttle could result in uncontrolled acceleration and great bodily injury or death. This product is intended for closed course racing by expert riders only. This product must be installed by experienced professional mechanic. Improper installation could result in great bodily injury or death. User assumes all responsibility for proper installation and use of this product. 070 Includes carb cap P/N 01-0039. Cap is attached to cable. 071 Fits Stock Carb; 4WD models require 11-0030 4x4 Switch Relocation Kit, sold separately. 072 +2.5 in. Housing is longer than OEM cable to allow for after-market clamps, bars, dampers, etc. 073 For use with stock fuel injection 074 Fork Bleeder Kit requires drilling, tapping and end milling of fork cap. Kit includes 5/16 inch tap and 9/32 inch drill bit. Requires 7/16 inch end mill (not included). 075 Non-USA Model 076 Requires 01-0742 cable with Stock Carb. 077 Requires 01-0236 cable w/ stock carb 078 For use with stock carb 079 For use with stock throttle bodies and Revolver throttle assembly only. IMPORTANT - The Revolver VR throttle does not have the starter and kill switch wiring or switches that are built into your stock throttle assembly. Use of the Revolver VR Throttle requires an aftermarket kill switch and starter button assembly (pn 11-0057) not included in kit. 080 Two inches longer than stock cable 081 “Warning: Installation of this kit requires drilling and tapping the carburetor body. Installation of this kit requires a high degree of skill and should only be done by an experienced mechanic with proper equipment (a drill press or mill is recom- mended). Improper installation will damage your carburetor. Motion Pro is not responsible for damage to carburetor resulting from misuse or improper installation.“ 082 Item discontinued 083 WARNING The Vortex throttle will open your carburetor to full throttle in just 46 degrees of twist (1/8 turn). This throttle is extremely fast and is recommended for closed course off-road racing by expert riders only. 084 WARNING: The Consumer Product Safety Improvement Act prohibits sale of this lever on vehicles intended for use by children 12 years or under. This lever also fits other bikes and ATVs designed for adult use and may be sold for use on adult model bikes and ATVs and for pit bike conversions for use by adults and children over 12. This lever may not be sold for use on bikes or ATVs intended for use by children ages 12 years or under. 085 WARNING: The Consumer Product Safety Improvement Act prohibits sale of this lever for for use on bikes or ATVs designed for children ages 12 years or under. 087 WARNING: Due to lead content, this product is intended for use on vehicles modified for adult use or for use by children over 12 years of age. The Consumer Product Safety Improvement Act prohibits sale of this product for use by children under 12 years of age. 088 Revolver cables can only be used with stock throttle body (or carburetor where applicable) and Revolver throttle 089 Fits WP 4357,4860 series forks with fork spring preload adjuster and 4860 MXMA CC series forks 090 We recommend using 14-0112 lever with this kit (not included in kit) 091 “For use with stock throttle bodies. Stock reel is _33.4 mm. IMPORTANT - The stock twist throttle assembly on this model incorporates an on/off switch, mode switch, and starter button. The Motion Pro 11-0057 accessory switch only has an on/off switch and starter button, and cannot be used to replace the original switching functions on the stock throttle assembly. In order to install the Revolver VR kit and retain all the necessary switching functions, owners of this model will need to install longer after market handlebars (at least 50 mm longer than stock on the right side) and use the stock throttle assembly mounted behind the Revolver VR throttle housing. The stock twist throttle assembly can be modified to remove the throttle reel holder portion and leave just the necessary switches. This modification makes it narrower and uses less space on the handlebar.“ 092 Fits both California and Non-California models (49 state) 093 “Some models may require use of a slip barrel at the carburetor and/or thumb throttle. (not included with cable). You can reuse the slip barrel that is on your vehicle or purchase this item separately from your local Suzuki dealer.“ 094 Fits front wheel. Drilling of rim may be required for installation on front rim. Or remove plug from rim where applicable 095 Revolver throttle kit featuring Chrome Revolver throttle housing. 096 Off road revolver throttle kits require a minimum of 200 mm of handlebar length in order to provide sufficient clearance between Revolver throttle housing and hydraulic brake lever 097 Throttle kit includes 11-0056 4x4 switch relocation plate 098 Polished aluminum. 2011 Stryker models which use polished levers are XVS13CACL,CAL, CAC0, and CA0. 2011 Stryker models which use black control levers are XVS13CAB and CACB (Black levers are not available for this model) 099 Will work with the stock Carb, S&S Super E & G with CV Bracket & late model Mikuni HSR carbs for use with CV cables 100 Built 2/16/10 and After 101 Lower front brake cable only 102 Replacement clutch cable only. Does not include engine side mounting bracket. For complete cable with bracket use part number 02-3007 (CRF250R) or 02-3008 (CRF450R). Requires use of Motion Pro mounting bracket and will not work with stock Honda bracket. 103 Includes engine side billet aluminum mounting bracket. For replacement cable only without bracket, use part number 02-3006.


2013 Moto En
To see the actual publication please follow the link above