Page 1420

2013 Moto En

1420 FLYWHEEL PULLER Flywheel puller 27mm x 1.0 l.H. Fits most late-model MX bikes Honda: CR80R/125R/250R/450R/480R/500R, XL80/100/100S/170, XR100/100R, FL250, ATC70/110 (CDI ONLY). ATC185/250R, TRX90 93-00, TRX70/125/250 & early 50cc Kawasaki: KD/KX/KDX80, KM100, KS100, KS125 & most two-stroke external flwheel models and earlier point-type ignitions. Suzuki: Quad Racers, 125/160EK/250R, DR100/125/200, DS80, ALT185, 50-125cc Trail & Street models & most late model RMs Yamaha: Most single cylinder off-road, enduro, MX, YZ & Quads with external flywheels 1968 & later, BW80, RIVA50, PW50, RD350, RZ350, TT500, XT500, YFM80/100/200/225, YFZ350, YSR50, YT125/175 & YZ400F KTM: 125/250 SX/EXC/MXC 98-00 & 250/300/380 SX/EXC/MXC 97-00 Flywheel puller (Tread: 27mm x 1.0 L.H.) 08-026 Flywheel puller for Honda 22mm x 1.5 R.H. Honda: FT/GB500, NT/NX650, TL250, VF500C/700C 84-86, VF700F/S, VF750C 82- 83, VF750F/S, VF1000F/R, VF1100C/S, VFR700/750F 86, VT500CC/FT, XL250/350/500/600, & XR500/600/650L Honda flywheel puller (Thread: 22mm x 1.5 R.H.) 08-074 Counter Balancer & Clutch Hub Spanner for Honda • Replaces 20mm end of Honda OEM tool 07716- 0020100 • Used to remove Honda OEM nut 90231-KY4- 900 • 4-Pin spanner made of heat-treated steel • Inside diameter is 20mm • Use with a 3/8” driver Fits Clutch Hub Nut on: PC50 69-70 S65 65-69 Z50 68-99 CRF450R 02-06 CRF450X 2005 Fits Crank Shaft Nut on: CA100 (Trail 50) 61-62 CA102 62-69 CA105 (Trail 50) 63-65 CA110 62-69 08-0385 Clutch puller for Honda FL250 Odyssey 22mm x 1.8 R.H. Honda FL250 Odyssey clutch puller (Thread: 22mm x 1.8 R.H.) 08-033 Flywheel puller M24 x 1.5 R.H. internal thread • Replaces Honda OEM tool 07AMC-MEBA 100 and Suzuki/Kawasaki OEM tool 57001-1565 • Includes shaft protector cap (OE reference 07AMC-MEBA110) • Fits Honda CRF 450R 02-06, CRF 450X 05-06, CRF250R/CRF250X 03-06, Kawasaki KX 250F 04-05, KX 450F 06, Suzuki RM-Z 250 04-06, RM-Z 450 05-06 CRF450R Flywheel puller (Thread: 24mm x 1.5 R.H. I.T.) 08-0257 Flywheel puller for Honda, Kawasaki and Suzuki Honda: CB750 69-78, most XL250R, XR200R/ XR250R/L & VF500F Kawasaki: KLR250, KLR600 & KLR650 Suzuki: SC650 99-01 et SV650S 01-02 Flywheel puller (Thread: 20mm x 1.5 R.H.) 08-085 Flywheel puller 18mm x 1.5 R.H. Fits: KLF110 96-00, KSF250 96-00, KZ200, KZ250, EZ250, KL250, KZ400, KZ440, EN500, EX500, KZ550, GPZ550, ZX600, KZ650, GPZ750, ZX750, VN750, KZ750, KZ900, KZ1000, KZ1100, GPZ1100 & KZ1300 Flywheel puller • Will also fit the Yamaha WR400F Flywheel • Puller kit for pulling magneto flywheel or starter gear on Kawasaki Jet Ski 300/440/500 • Includes three 6 x 25 and three 8 x 40 bolts 08-0160 Flywheel puller for KTM 4-stroke M26 x 1.0 R.H. Internal thread • Replaces OEM took 580.12.009.000. • Includes shaft protector cap (OE reference 510.12.016.000) • Not applicable to older models with Motoplat ignition systems.. KTM 4-Stroke Flyweel Puller (Thread: 26mm x 1.0 R.H. I.T.) 08-0293 Flywheel puller for Honda Fits: XR400, CB400A/T 78-79, CB450SC, CM450, CMX450C, CX500TC, CX650, GL500/650, MR250, NX250,PC800, VF700C 87, VF750C 88, VT700C/750C/800C/1100C, ATC250SX/350X, TRX250/300/300FW, TRX300EX 93-02, TRX400EX 99-02, VFR800FI 98-00 & VTR250 Honda (Thread: 20mm x 1.5 Hollow R.H.) 08-086 Flywheel Puller M30 x 1.0 R.H. Internal • Replaces OEM tool YM04141 Yamaha: WR 250F 03-05 08-0386 Flywheel Puller 16mm x 1.5 R.H. Honda: ATC90, ATC110 with breaker points, CB175, CT90/350G/360/500/500T, CM185/200T/450, CMX250, Early CR125/250MX, SL175/350 Kawasaki: KH400A, KLF300 86-87, KLT110/200, KX125/250/420/500 pré-81 models, KZ10000/1300 & Z1 Suzuki: GS550/650/750/Early 1100 & most 4-stroke street models Yamaha: Most 4-stoke street models & 250/350 electric start 2-stroke twins, FJ600/750/1000 Flywheel puller (thread: 16mm x 1.5 R.H.) 08-027 Kawasaki Flywheel puller (Thread: 18mm x 1.5 R.H.) 08-1160


2013 Moto En
To see the actual publication please follow the link above